Inverter 12/375 VE.Direct Schuko
Inverter 12/375 VE.Direct Schuko Applications Refrigerator, laptop, tool charger, or a small pump: where there is no mains connection, this device supplies 230 V. Compact enough for a camper, cabin, or technical room, and with ECO mode economical enough to remain permanently on the battery bank. * Campers, vans, and service vehicles on 12 V * Sloops, sailboats, and smaller pleasure craft * Garden sheds, chalets, and off-grid accommodations * Metering cabinets, telecom locations, and pump installations in rural areas * Backup for equipment that must continue operating during a power outage Power and starting behavior * 375 VA nominal; 300 W continuous at 25 °C, 260 W at 40 °C * 700 W peak power for starting currents of LED drivers, incandescent lamps, and power tools * Pure sine wave, suitable for sensitive electronics * Full bridge with toroidal transformer; Short-circuit proof and protected against overheating due to overload or high ambient temperature * Maximum efficiency 89% ECO mode If the load drops below the set threshold, the inverter switches to standby and scans every 2.5 seconds by default to see if there is demand again. The minimum generating power is 15 W by default; both values are adjustable. Consequently, the no-load power drops from 5.6 W to 0.9 W. The correct setting depends heavily on the type of load: inductive, capacitive, or non-linear. Expect a brief on-site adjustment. Battery monitoring and shutdown * Input voltage range 9.2 – 17 V * Low battery voltage shutdown default 9.3 V, adjustable * Restart and alarm at 10.9 V, battery charged detection at 14.0 V, both adjustable * Dynamic shutdown: the shutdown level follows the load, ensuring the battery bank continues to be utilized under light load * Protected against short circuit, overload, over- and under-battery voltage, over-temperature, and excessive DC ripple voltage, with automatic restart VE.Direct port * Read out and configure via VictronConnect on smartphone or tablet with a VE.Direct Bluetooth Smart dongle * Connection to a PC via a VE.Direct-to-USB interface cable * Adjustable: output voltage 210 – 245 V, frequency 50 or 60 Hz, ECO threshold and search interval, alarm and shutdown levels * Monitoring of battery voltage, AC output voltage, load indication, and alarms Connection and mounting * Schuko socket (CEE 7/4) on the device * DC side on screw terminals, maximum cable cross-section 10 mm²; battery cables are not included * Minimum battery capacity 40 Ah * Recommended DC cable: 6 mm² up to 1.5 m, 10 mm² for 1.5 to 3 m * Internal DC fuse 2 x 40 A (ATOF 32 V), non-replaceable; for a DC cable longer than 1.5 m, an additional fuse or DC circuit breaker close to the battery bank is mandatory * Connection for an external on/off switch on the two-pole plug, or between the battery positive terminal and its left contact — useful for switching in conjunction with the ignition switch in a vehicle * Can be mounted vertically or horizontally with four screws, minimum 10 cm clearance all around; IP21 applies only with flush mounting according to the manual; in other positions IP20 * Connecting the battery cables in reverse will cause the internal fuse to blow and may damage the device. Can be ordered directly with this * Victron VE.Direct Bluetooth Smart dongle (https://shop.top.systems/monitoring-controle/draadloos/victron-ve-direct-bluetooth-smart-dongle.html) (ASS030536011) — read out and configure via VictronConnect. Category: Monitoring & control > Wireless (https://shop.top.systems/monitoring-controle/draadloos/) * Red battery cable 6mm² per meter (https://shop.top.systems/assortiment/details/?webgroupfilter=14&artdetail=KABRD0100600) (KABRD0100600). Category: Installation > Cables > Battery (https://shop.top.systems/installatie/kabels/accu/) * Battery cable black 6mm² per meter (https://shop.top.systems/assortiment/details/?webgroupfilter=14&artdetail=KABZW0100600) (KABZW0100600). Category: Installation > Cables > Battery (https://shop.top.systems/installatie/kabels/accu/) * Crimp cable lug 6mm² > M6 (https://shop.top.systems/assortiment/details/?webgroupfilter=14&artdetail=PSKABOG00006) (PSKABOG00006). Category: Installation > Cable accessories > Crimp lugs (https://shop.top.systems/installatie/accessoires-kabels/perskabelogen/) * Crimp lug 6mm² > M8 (https://shop.top.systems/assortiment/details/?webgroupfilter=14&artdetail=PSKABOG00007) (PSKABOG00007). Category: Installation > Cable accessories > Crimp lugs (https://shop.top.systems/installatie/accessoires-kabels/perskabelogen/) For a cable length between 1.5 and 3 m, 10 mm² is required; you can find this in the Battery cables category (https://shop.top.systems/installatie/kabels/accu/). From 1.5 m upwards, an external fuse with holder is also required, to be matched to the cable and installation: see Fuses (https://shop.top.systems/beveiligen-schakelen/zekeringen/) and Fuse holders (https://shop.top.systems/beveiligen-schakelen/zekeringhouders/). Documentation * Manual Inverter VE.Direct 250VA – 1200VA (NL, EN, FR, DE, ES, IT — PDF) (https://www.victronenergy.com/upload/documents/Manual-Inverter-VE.Direct-250VA-1200VA-EN-NL-FR-DE-ES-IT-.pdf) * Datasheet Inverter VE.Direct 250VA – 1600VA (EN, PDF) (https://www.victronenergy.com/upload/documents/Datasheet-Inverter-VE.Direct-250VA-1600VA-EN.pdf) * Dimensions Inverter VE.Direct 12V/24V/48V 250VA 375VA (PDF) (https://www.victronenergy.com/upload/documents/Inverter-VE.Direct-12V-24V-48V-250VA-375VA.pdf) * Declaration of Conformity Inverter VE.Direct 250VA – 1200VA (PDF) (https://www.victronenergy.com/upload/documents/Inverters-VE.Direct-250VA-1200VA-230V50Hz-and-110V60Hz-2023-10-11.pdf) * Safety Certificate IEC 60335-1 / AS-NZS 4736 – 250VA, 375VA, 500VA (PDF) (https://www.victronenergy.com/upload/documents/Certificate-Safety-IEC-60335-1-AS-NZS-4736-Phoenix-Inverter-VE.Direct-250-375-500VA.pdf) * ECE R10-6 Certificate – VE.Direct Inverter 250VA, 375VA, 500VA (PDF) (https://www.victronenergy.com/upload/documents/Certificate-Automotive-ECE-R10-6-Inverter-VE.Direct-250VA,-375VA,-500VA.pdf) * ECE R10-5 Certificate – Phoenix Inverters 250VA, 375VA, 500VA (PDF) (https://www.victronenergy.com/upload/documents/Certificate-Automotive-ECE-R10-4-–-Phoenix-Inverters-250VA,-375VA,-500VA.pdf) * ISO 9001 Certificate (PDF) (https://www.victronenergy.com/upload/documents/ISO9001-certificate-2024-EN.pdf) * VE.Direct HEX Protocol Phoenix Inverter (EN, PDF) (https://www.victronenergy.com/upload/documents/VE.Direct-HEX-Protocol-Phoenix-Inverter.pdf) Videos * Did You Know – Reduce power consumption of an inverter in standby (EN) (https://www.youtube.com/watch?v=v0s0x0hf66I) Contact Battery capacity, cable length, and ECO setting determine whether this device performs as your customer expects in practice. As an official Victron distributor, we supply from our own stock in Bodegraven and directly from the Victron Energy warehouse, and our engineers will calculate it for you in just a few minutes. Contact us (https://www.top.systems/nl/contact/) for advice or a quote. Specifications System voltage 12 Vdc Nominal power 375 VA Continuous power at 25 °C 300 W Continuous power at 40 °C 260 W Peak power 700 W Output voltage 230 VAC ±3 %, adjustable 210 – 245 V Frequency 50 or 60 Hz ±0.1 %, adjustable Waveform Pure sine wave Input voltage range 9.2 – 17 V Low battery voltage shutdown 9.3 V, adjustable Restart and low battery voltage alarm 10.9 V, adjustable Battery charged detection 14.0 V, adjustable Dynamic shutdown Load-dependent, configurable Maximum efficiency 89 % No-load power 5.6 W No-load power in ECO mode 0.9 W ECO mode Yes; Standard wake-up power 15 W, standard search interval 2.5 s, both adjustable Communicative VE.Direct AC output Schuko socket (CEE 7/4), 1 piece AC input No DC connection Screw terminals, maximum 10 mm² Minimum battery capacity 40 Ah Recommended DC cable 6 mm² up to 1.5 m; 10 mm² at 1.5 – 3 m Internal DC fuse 2 x 40 A, type ATOF 32 V, non-replaceable Remote on/off Yes, via two-pole plug Automatic changeover switch Filax or Multi Protection class IP21 (IP20 with different mounting position) Operating temperature -40 to +60 °C, fan cooling; above 40 °C 1.25% power degradation per °C Humidity Maximum 95%, non-condensing Dimensions (hxwxd) 86 x 165 x 260 mm Weight 3.0 kg Housing Steel frame with plastic cover Safety standards EN/IEC 60335-1, EN/IEC 62109-1 EMCEN standards 55014-1, EN 55014-2, IEC 61000-6-1, IEC 61000-6-3 Vehicle directive ECE R10-4, EN 50498 Brand Victron Energy Warranty 5 years We would be happy to provide you with more information about this product. Please contact us
contact join us.
